RX_ADC_RAW_EN=0, RX_SRC_RATE=0, RX_IQ_SWAP=0, RX_CH_FILT_BYPASS=0, RX_ADC_POL=0, RX_FSK_ZB_SEL=0, RX_RSSI_EN=0, RX_DEC_FILT_OSR=0, RX_AGC_EN=0, RX_DEC_FILT_SAT_I=0, RX_SRC_EN=0, RX_DC_RESID_EN=0, RX_DEC_FILT_SAT_Q=0, RX_DEC_FILT_HAZARD=0, RX_DCOC_CAL_EN=0, RX_RSSI_FILT_HAZARD=0, RX_DCOC_EN=0, RX_NORM_EN=0, RX_ADC_NEGEDGE=0
RX Digital Control
| RX_ADC_NEGEDGE | Receive ADC Negative Edge Selection 0 (0): Register ADC data on positive edge of clock 1 (1): Register ADC data on negative edge of clock |
| RX_CH_FILT_BYPASS | Receive Channel Filter Bypass 0 (0): Channel filter is enabled. 1 (1): Disable and bypass channel filter. |
| RX_ADC_RAW_EN | ADC Raw Mode selection 0 (0): Normal operation. 1 (1): The decimation filter’s 12bit output consists of ADC samples in the 8 LSBs. This is for test purposes only to observe ADC output via XCVR DMA or DTEST. |
| RX_ADC_POL | Receive ADC Polarity 0 (0): ADC output of 1’b0 maps to -1, 1’b1 maps to +1 (default) 1 (1): ADC output of 1’b0 maps to +1, 1’b1 maps to -1 |
| RX_DEC_FILT_OSR | Decimation Filter Oversampling 0 (0): OSR 4 1 (1): OSR 8 2 (2): OSR 16 3 (3): OSR 6 4 (4): OSR 32 5 (5): OSR 12 6 (6): OSR 24 |
| RX_FSK_ZB_SEL | FSK / 802.15.4 demodulator select 0 (0): FSK demodulator. 1 (1): 802.15.4 demodulator. |
| RX_NORM_EN | Normalizer Enable 0 (0): Normalizer is disabled. 1 (1): Normalizer is enabled. |
| RX_RSSI_EN | RSSI Measurement Enable 0 (0): RSSI measurement is disabled. 1 (1): RSSI measurement is enabled. |
| RX_AGC_EN | AGC Global Enable 0 (0): AGC is disabled. 1 (1): AGC is enabled. |
| RX_DCOC_EN | DCOC Enable 0 (0): DCOC is disabled. 1 (1): DCOC is enabled. |
| RX_DCOC_CAL_EN | DCOC Calibration Enable 0 (0): DCOC calibration is disabled. 1 (1): DCOC calibration is enabled. |
| RX_IQ_SWAP | RX IQ Swap 0 (0): IQ swap is disabled. 1 (1): IQ swap is enabled. |
| RX_DC_RESID_EN | DC Residual Enable 0 (0): DC Residual block is disabled. 1 (1): DC Residual block is enabled. |
| RX_SRC_EN | RX Sample Rate Converter Enable 0 (0): SRC is disabled. 1 (1): SRC is enabled. |
| RX_SRC_RATE | RX Sample Rate Converter Rate Selections 0 (0): SRC is configured for a First Order Hold rate of 8/13. 1 (1): SRC is configured for a Zero Order Hold rate of 12/13. |
| RX_DMA_DTEST_EN | RX DMA and DTEST enable |
| RX_DEC_FILT_GAIN | Decimation Filter Fractional Gain |
| RX_DEC_FILT_HZD_CORR_DIS | Decimator filter hazard correction disable |
| RX_DEC_FILT_HAZARD | Decimator output, hazard condition detected 0 (0): A hazard condition has not been detected 1 (1): A hazard condition has been detected |
| RX_RSSI_FILT_HAZARD | Decimator output for RSSI, hazard condition detected 0 (0): A hazard condition has not been detected 1 (1): A hazard condition has been detected |
| RX_DEC_FILT_SAT_I | Decimator output, saturation detected for I channel 0 (0): A saturation condition has not occurred. 1 (1): A saturation condition has occurred. |
| RX_DEC_FILT_SAT_Q | Decimator output, saturation detected for Q channel 0 (0): A saturation condition has not occurred. 1 (1): A saturation condition has occurred. |